ELECTRICAL AND MECHANICAL ROTATING EQUIPMENT
Hotel Ibis, Yogyakarta | 1 – 3 Juli 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 8 – 10 Juli 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 15 – 17 Juli 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 22 – 24 Juli 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 29 – 31 Juli 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 12 – 14 Agustus 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 19 – 21 Agustus 2013 | Rp 5.500.000,- per peserta
Hotel Ibis, Yogyakarta | 26 – 28 Agustus 2013 | Rp 5.500.000,- per peserta
Jadwal Training 2013 Selanjutnya …
COURSE OVERVIEW
This course is an integral part of the programme, has a duration of few days, and covers equipment driven directly by gas turbines or indirectly through gas turbine driven generator sets, electrical power systems and motor drivers. Typical applications are for Oil, Gas and other industries
OUTLINES
Gas Turbine Engines
The basic principles underpinning the operation of the gas turbine will be presented. This section will also include a description of the following cycles:- simple, reheat, recuperated, inter-cooled, combined gas and steam and steam injected. The effects of engine rating, variation in efficiencies between engines, maintenance intervals and fuel quality are introduced.
Pumps and Compressors
The basic principles of rotor dynamic and positive displacement pumps and compressors and the effects of cavitation, compressibility, viscosity variation and humidity. Losses in fluid systems and interaction between machines and systems. Introduction to the basic design principles of pumps and compressors, involving shafts, bearings and seal systems. A discussion of the regulation of pumps and compressors. The correct selection and application of pumps and compressors.
Electrical Power Systems
Power System Design covering voltage and frequency control, maximum and minimum system fault levels. A demonstration of power system simulation by computer studies including load flow, voltage drop, short circuit levels, motor starting performance and protection grading.
Electrical Power Generation
An overview of the electrical features of power generation. The mechanical engineer is involved as a member of a design team, often as the lead engineer, with the important requirement of discussing electrical design features with specialist engineers and then being expected to take part in the decision making process for a power generation package. Design, construction and specification of synchronous machines (generators) with typical data sheets.
Electric Motors Drive Systems
Design and construction features of asynchronous machines (motors), load characteristics, active and reactive load sharing, power transfer between power systems. Matching motors to the driven equipment and effect of power supply system variations. Specifications in relation to IEC/BSS standards. Data sheets for the selection and purchase of electrical machines. Electrical Variable Speed Drive Systems with power electronics and various types of convertors, applications to motors and generators, effect on driven equipment. Data sheets for the selection and purchase of systems.
Aspects of Electrical Machines
Hazardous area protection, electrical power three phase calculations with worked examples and typical values that can be used during project evaluations. Operation and Maintenance plans and common failures. Digital microprocessor systems interfacing with plant control systems for the control, protection and retained information on motor performance.
Selection of Drivers
When driving rotating equipment a key aspect of any project is the decision on whether pumps or compressors are to be driven by gas turbine engines or by electric motors from a power system with the option of local gas turbine driven power generation. Each project will always have its own particular solution.
Design Workshop
Workshop exercises in which machines are chosen to meet an outline brief for a pump or compressor plant with the appropriate direct or electric motor drive and its control system will be undertaken.
Waktu dan Tempat
Jadwal Training 2013 : ELECTRICAL AND MECHANICAL ROTATING EQUIPMENT
Hotel Ibis, Malioboro, Yogyakarta
02-04 Januari 2013
07-09 Januari 2013
14-16 Januari 2013
21-23 januari 2013
28-30 Januari 2013
04-06 Februari 2013
11-13 Februari 2013
18-20 Februari 2013
25-27 Februari 2013
04-06 Maret 2013
13-15 Maret 2013
18-20 Maret 2013
25-27 Maret 2013
01-03 April 2013
08-10 April 2013
15-17 April 2013
22-24 April 2013
29 April – 01 Mei 2013
06-08 Mei 2013
13-15 Mei 2013
20-22 Mei 2013
27-29 Mei 2013
03-05 Juni 2013
10-12 Juni 2013
17-19 Juni 2013
24-26 Juni 2013
01-03 Juli 2013
08-10 Juli 2013
15-17 Juli 2013
22-24 Juli 2013
29-31 Juli 2013
12-14 Agustus 2013
19-21 Agustus 2013
26-28 Agustus 2013
02-04 September 2012
09-11 September 2013
16-18 September 2012
23-25 September 2013
30 September – 02 oktober 2013
07-09 Oktober 2013
16-18 Oktober 2013
21-23 Oktober 2013
28-30 Oktober 2013
06-08 November 2013
11-13 November 2013
18-20 November 2013
25-27 November 2013
02-04 Desember 2013
09-11 Desember 2013
16-18 Desember 2013
23-24 Desember 2013
30-31 Desember 2013
INVEST & FACILITY
Rp.5.500.000 (Non Residential)
Fasilitas : Certificate,Training kits, USB,Lunch,Coffe Break, Souvenir
Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel (khusus bagi perusahaan yang mengirimkan minimal 3 orang peserta)
INSTRUCTUR
Tugino, ST., MT
Formulir Permintaaan Informasi Lanjutan / Pra-Pendaftaran Public Training
INFORMATION OPTIONS
Judul Training (required)
Tanggal Training
Select a message type
(required)
PERSONAL DATA
Your Name (required)
Job Title (required)
Company (required)
Company Address
Email (valid email required)
Mobile Phone (required)
Office Phone (required)
Extention No.
Facsimile (Fax)
Website
PRE REGISTRATION DATA (Tidak Mengikat)
Penanggung Jawab Training di Perusahaan
Email
Office Phone+Ext atau No. Handphone
Jumlah Peserta (required)
Nama-nama peserta
Payment Method
MESSAGE FOR TRAINING PROVIDER
Pesan untuk penyelenggara Training
CC this registration / message to me
cforms contact form by delicious:days
Incoming search terms:
info training rotating equipment di yogyakarta 2013
jadwal training rotating equipment july 2013
rotating equipment engine control training outline
traning mechanical engineering di yogyakarta 2013