2016-08-01

Table of Contents

Introduction

1.1  What is a Microcontroller?

1.2  Why are Microcontrollers used?

2        Getting started

2.1  Parts list and vendors

2.2  Connecting the equipment

3        PIC16fF877 Microcontroller

3.1  Flash PIC development board

3.2  CCS PIC-C compiler

3.3  In Circuit Debugger/Programmer (ICD-S)

3.4  Embedded C Programming and the Microchip PIC

4        Experiments on PIC16F877

4.1  LED

4.2  Dip Switch

4.3  ADC Temperature Measurement

4.4  Open Loop and Closed Loop Temperature Control

5        Where do we go from here?

Introduction

This tutorial is to introduce the microcontroller technolgy the capabilities and the specifications of a commonly used Microcontroller Microchip PIC16F877 and describe the experiments conducted using the Development board Flash PIC development board which accomodates this microcontroller.



1.1.   What is a microcontroller?

A microcontroller is a compact standalone computer, optimized for control applications. Entire processor, memory and the I/O interfaces are located on a single piece of silicon so, it takes less time to read and write to extrernal devices.

1.2.   Why are microcontrollers used?

Following are the reasons why microcontrollers are incorporated in control systems:

Cost: Microcontrollers with the supplemantary circuit components are much cheaper than a computer with an analog and digital I/O

Size and Weight: Microcontrollers are compact and light compared to computers

Simple applications: If the application requires very few number of I/O and the code is relatively small, which do not require extended amount of memory and a simple LCD display is sufficient as a user interface, a microcontroller would be suitable for this application.

Reliability: Since the architecture is much simpler than a computer it is less likely to fail.

Speed:  All the components on the microcontroller are located on a singe piece of silicon. Hence, the applications run much faster than it does on a computer.

Getting Started

2.1.   Parts list:

The parts list and the vendor list is given in Table-2.1.1

Description

Vendor

Part No.

Price

Qty.

FlashPIC-Development Board

PRLLC

FlashPIC-Dev

45.00$

1

CCS ICD-S debugger/programmer

PRLLC

ICD-S

75.00$

1

Embedded C Programming and the Microchip PICRichard H. Barnett,Larry D. O’Cull,Sarah A. CoxISBN: 1401837484

Amazon.com

N/A

57.70$

1

12VDC adapter

Radioshack

273-1776

16.99$

1

8 position dip switch

Jameco

38842

0.89$

1

Multipurpose PC Board

Radioshack

276-150

$1.69

1

LM35CZ Linear Series

Jameco

107107

$5.79

1

Plastic Sphere

Bubblegum machine

DAC-0832 8 bit DAC

Jameco

128186

3.95

1

LF353 Op-Amp

Jameco

22939

$.39

1

10Kohm Resistor

Radioshack

271-1335

$.99

1

20Kohm Resistor

Radioshack

271-0265

$.99

2

10ohm 10W Resistor

Radioshack

271-132

$1.69

1

TIP31 Power Transistor

Jameco

33048

$.49

1

0.01uF Capacitor

Radioshack

272-1051

$1.19

1

1N4004 Diode

Radioshack

276-1103

$.79

1

100 ohm resistor

Radioshack

271-1311

$.99

1

Technie Toyz 12V PC Fan

Compusa

MD-TTF-8025A-2B

$10.99

1

9V battery

Radioshack

23-875

$3.29

1

6-Ft. Serial RS-232C Cable

Radio Shack

26-117

$13.49

1

1×40 pin header

Jameco

103270

0.75$

1

Note: It is assumed that the user has the following common electrical equipment: 1×8 pin ribbon cable, alligator clips, soldering iron and solder.

2.2.   Connecting the equipment

Powering up the PIC Development Board

The PIC16F877 chip has to be powered at all times when its being programmed and running an application.

Cut the connector off the DC end of the 12VDC adapter and strip the wire ends.

Determine the + and – wire leads using a voltmeter.

Apply the 12VDC to the board by connecting the 12VDC adapter to + and – pins of J2 of Flash PIC Development Board. See Figure2.2-1

Caution: Make sure you wire the – and + ends of the adapter of the to the right pins of Jumper 2. Do not plug the adapter to 110V/AC outlet before you wire the power to the board. In order to avoid cheking the leads with a voltmeter everytime, its always a good practice to label the leads for future reference.

Plug the adapter to the 110V/AC outlet.

Observe the green LED D9 illuminating and rest of the LEDs flashing in order.

b.Connecting the Flash PIC Development Board to a PC through ICD-S:

After we put power on the FlashPIC development board, now we are ready to program the PIC16F877 chip.

Connect the ICD-S to the computer using the RS-232 cable, which came with the ICD-S.

Conncect the ICD-S to the developmet board using the phone jack.

Coding,Compiling and Transfering the .hex files to the chip

Now that we have our hardware setup, we are ready to write the code and transfer the .hex files to the PIC16F877.

Install the CCS compiler demo version, which came with the reference book ”Embedded C Programming and the Microchip PIC” to your computer

Insall the ICD software which came with the ICD-S unit.

Start the CCS compiler.

Go to menu path: Options>Debugger/Programmer

Change the to the path of Icd.exe. (See Figure2.2-3)This would enable starting the ICD-S software via toolbar button.

6. The software setup is complete. We can type the source code and compile it and transfer the file to the PIC chip as illustrated in Figure2.0-3. After single clicking the “compile” command button on the toolbar and generating the .hex file, we can single click the “program chip” command button.

7. After the “program chip” command button is pressed the ICD V2.7 program is initiated. First we check the RS-232 communications, the ICD-S and the PIC16F877 by using the following command buttons respectively: “Check COMM”, “Test ICD”, “Test Target”. If all of them check to be OK, now we can browse and transfer the .hex file to the chip by using “Download to target Command button”. After the .hex file is transferred, now we can run the software and test its functionality by clicking on “Run Program” command button. (Figure2.2-4)

8. Since the software is tested now the ICD-S can be disconnected and the Development board can be powered up and the .hex file can be run without being connected to the computer.

PIC16F877 Microcontroller

In this section, properties of PIC16F877 microcontroller,CCS compiler, ICD-S, the reference book “Embedded C programming and the microchip PIC” are briefly explained to give a general idea; it may seem confusing for a first time reader who is not familiar to microcontrollers technology or C programming. However, as the funtionality of the components such as timers, A/D converters, I/O Ports are explained in detail in Section 3 as they are being used in the experiments, the fundemental concepts would be better understood and, the reader can flashback to this section to view the schematics and the specifications.

PIC16F877 is one of the most commonly used microcontroller especially in automotive, industrial, appliances and consumer applications. In Figure –1, the block diagram of the PIC16F877 is illustrated.

The core features of PIC16F877 are:

High performance RISC CPU

Only 35 single word instructions to learn

All single cycle instructions except for program

branches which are two cycle

Operating speed: DC – 20 MHz clock input

DC – 200 ns instruction cycle

Up to 8K x 14 words of FLASH Program Memory,

Up to 368 x 8 bytes of Data Memory (RAM)

Up to 256 x 8 bytes of EEPROM Data Memory

Pinout compatible to the PIC16C73B/74B/76/77

Interrupt capability (up to 14 sources)

Eight level deep hardware stack

Direct, indirect and relative addressing modes

Power-on Reset (POR)

Power-up Timer (PWRT) and

Oscillator Start-up Timer (OST)

Watchdog Timer (WDT) with its own on-chip RC

oscillator for reliable operation

Programmable code protection

Power saving SLEEP mode

Selectable oscillator options

Low power, high speed CMOS FLASH/EEPROM

technology

Fully static design

In-Circuit Serial Programming. (ICSP) via two

pins

Single 5V In-Circuit Serial Programming capability

In-Circuit Debugging via two pins

Processor read/write access to program memory

Wide operating voltage range: 2.0V to 5.5V

High Sink/Source Current: 25 mA

Commercial, Industrial and Extended temperature

ranges

Low-power consumption:

– < 0.6 mA typical @ 3V, 4 MHz

– 20 μA typical @ 3V, 32 kHz

–         < 1 μA typical standby current

The peripheral features of the PIC16F877 are:

Timer0: 8-bit timer/counter with 8-bit prescaler

Timer1: 16-bit timer/counter with prescaler,

can be incremented during SLEEP via external

crystal/clock

Timer2: 8-bit timer/counter with 8-bit period

register, prescaler and postscaler

Two Capture, Compare, PWM modules

Capture is 16-bit, max. resolution is 12.5 ns

– Compare is 16-bit, max. resolution is 200 ns

– PWM max. resolution is 10-bit

10-bit multi-channel Analog-to-Digital converter

Synchronous Serial Port (SSP) with SPI. (Master

mode) and I2C. (Master/Slave)

Universal Synchronous Asynchronous Receiver

Transmitter (USART/SCI) with 9-bit address

detection

Parallel Slave Port (PSP) 8-bits wide, with

external RD, WR and CS controls (40/44-pin only)

Brown-out detection circuitry for

Brown-out Reset (BOR)

3.1.   Flash PIC development board

Usually, a microcontroller by itself is not sufficient to perform the intended tasks. For instance, an oscillator chip is necessary to time the programmed instructions. In order to investigate the capabilities or to test a given microcontroller, obviously it is vital to build the proper circuitary. Example: potentiometer and a power supply to simulate analog inputs or LEDs to simulate the digital outputs. Hence, some hardware and sofware vendors provide the microcontroller with the supplemantary circuit elements on the same breadboard. These boards are called Development Boards. One can also build a development board himself/herself if he/she is willing to go through the painsaking process of building the circuit.

The development board used in the series of experiments is Flash PIC development board. (Figure3.1-1) It has the following features:

– RS232 through a 9-Pin D-Shell as well as screw terminals and a jumper header.

– Up to 32K words of In-System Programmable FLASH memory with up to 256

bytes of EEPROM and up to 1.5K of Internal RAM (depending on processor

selection).

– Up to 8, 10 bit, Analog Inputs, using either internal or user supplied reference.

– 9 I/O controlled LEDs, 8 of which are jumper selectable.

– 32KHz “watch” crystal for on-board Real-Time operations.

– A universal clock socket allows for “canned oscillators”, as well as a variety of

crystals, ceramic resonators, and passive terminations.

– 0.1” centered headers provide for simple connection to the processor special

function pins and I/O.

– A 6-pin, ICD connection is provided for in-system programming and debugging.

This connection is directly compatible with the Microchip ICD, ICD2 and CCS

ICD-S programming hardware. Flash PICs can also be programmed through

RS232 using an appropriate boot loader application.

– On-board regulation allows for power inputs from 8-38VDC with an LED power

indicator.

– Termination is provided for 5VDC output at 250ma

3.2.   CCS PIC-C compiler

The CCS PCW compiler is specially designed to meet the special needs of the PICmicro MCU controllers. These tools allow developers to quickly design application software for these controllers in a highly readable, high-level language.

The compilers has some limitations when compared to a more traditional C

compiler. The hardware limitations make many traditional C compilers

ineffective. As an example of the limitations, the compilers will not permit

pointers to constant arrays. This is due to the separate code/data segments in

the PICmicro MCU hardware and the inability to treat ROM areas as data. On

the other hand, the compilers have knowledge about the hardware limitations

and do the work of deciding how to best implement your algorithms. The

compilers can efficiently implement normal C constructs, input/output operations

and bit twiddling operations.

The compiler can output 8 bit hex, 16 bit hex, and binary files. Two listing formats

are available. Standard format resembles the Microchip tools and may be

required by some third-party tools. The simple format is easier to read. The

debug file may either be a Microchip .COD file or Advanced Transdata .MAP file.

All file formats and extensions are selected via the Options|File Formats menu

option in the Windows IDE.

The usage of the copiler is explained in Section 2.0 Getting started. The reference book “Embedded C Programming and the Microchip PIC” comes with a demo version of the compiler.

3.3.   ICD-S Debugger/Programmer

The ICD-S programmer is the hardware/firmware interface to burn the .hex files to the Microchip PIC. The ICD unit works with CCS’s PCW debugger or CCS’s stand-alone ICD control software. CCS’s PCW debugger is a very robust debugger integrated with PCW, and provides very detailed debugging information at the C level. The stand-alone control software allows you to quickly program target chips using ICD’s ICSP. The control software also lets you update the ICD unit’s firmware without having to remove the chip from the ICD unit. (Using these software tools requires you to have loaded the CCS-ICD firmware onto the ICD unit, which is loaded by default).

Authors note 01/22/04 : I found it odd that prllc.com does not provide a freeware program like “AVR bootloader.exe” for FlashPIC Development board as they do for Atmel AVR development board, that would enable programming the chip via serial communication connector P1 in-built to the development board. I don`t think that Development board and Compiler vendors should force the costumers to buy products like ICD-S where an option like programming via serial link exists. I have seen a program in http://sjeffroy.free.fr/Prog__PIC/BootLoader/bootloader.html which seems like it might work given the fact that bootloader file “loader.hex” pre-exists on the chip. Personally, I did not try running this program and programming the chip via RS-232.

3.4.   The Reference Book: Embedded C Programming and the Microchip PIC by Barnett, Cox and O’Cull

This book is a good guide for introducing the microcontroller technology. First chapter is dedicated to teaching basic C programming however, this book shouldn’t be considered a C programming handbook. One should always have a book like: Teach yourself C by Zhang ISBN 0-672-31861 as a C programming reference guide for beginners.

This book is designed to teach C language programming as it applies to embedded microcontrollers and to fuel knowledge in the application of the Microchip family of PIC microcontrollers. Coverage begins with a step-by-step exploration of the C language showing readers how to create C language programs to solve problems. PIC processors are then studied, from basic architecture to all of the standard peripheral devices included in the microcontrollers. Numerous worked-out example programs demonstrate common uses for each of the peripherals. Readers are subsequently introduced to the built-in functions available in C, to speed their programming and problem solving. Finally, readers are taken through use of the C Compiler, and to help custom learn to efficiently develop projects.

Included with the book is a CDROM containing samples all of the example programs from the book as well as an evaluation version of the CCS-PICC Compiler.

Author`s note 01/22/04 : In the first examples and projects in chapter 1, functions like “scanf” and “printf” are used that require prior knowledge to interface the board through RS-232 which is introduced in the late chapters of the book. It might be discouraging for the student not being able to do the first project of the book, hands-on. Although I was able to find answers to most of my questions about using the C compiler and the hardware however, I had to do a lot of skipping between chapters and Appendixes to find these answers which was time consuming. In general it is a nice and descriptive text book.

Experiments

The most quick and effective way of learning a new topic is, having hands on experience. In this section we will conduct some experiments using the FlashPIC Development board to which would give us a jump start on in PIC usage.

4.1.   LED Experiment

The digital I/O and the timers will be discussed with this experiment. The program will count from 0 to 255 and output the binary equivalent of this number to PortD every 2 seconds. The digital I/O peripherals are discussed in detail in the next experiment “Dipswitch”. In this experiment we will focus on the usage timers.

Timers and counters are one of the most commonly used perpheral in a microcontroller. They can be used to measure time periods, speed and provide output signals in a specified rate.

The PIC16F877 has 4 timers timer0, timer1, timer2 and watch dog timer. Timer0 and timer2 are 8 bit timers and timer1 is a 16bit timer. The inportant issue is to know when the counter reaches the maximum value (255 in 8 bit timers and 65,535 is 16bit timers) and rolls over.



The watch dog timer is a safety device. When an unepected event occurs, the watch dog timer resets the microcontroller. In this experiment we will use the watch dog timer as our timer to time the digital output.

#use delay(clock=10000000, RESTART_WDT)

The command line above, is used to tell the compiler to insert an appropriate code to automatically reload the WDT during delay functions.

“delay_ms(2000)”  command line is used to place a delay the event 2000ms in every cycle of the while loop. “output_d(z)” command line is used to output the digital number through portD.

For more detail: Microchip PIC16F877 Microcontrolle

The post Microchip PIC16F877 Microcontrolle appeared first on PIC Microcontroller.

Show more