Crude Oil
1. Crude oil is the term for “unrefined” oil, the substance that comes out of the ground. It is also known as petroleum. Crude oil is a fossil fuel, meaning that it was made naturally from decaying plants and animals living in ancient seas millions of years ago. Most places you can find crude oil were once sea beds. Crude oils vary in color, from clear to tar-black, and in viscosity, from water to almost solid.
Crude oils are such a useful starting point for so many different substances because they contain hydrocarbons. Hydrocarbons are molecules that contain hydrogen and carbon. They come in various lengths and structures, from straight chains to branching chains to rings.
CRUDE OIL COMPONENTS
Crude oil are made of the following elements or compounds:
Carbon 84%
Hydrogen 14%
Sulfur 1 to 3% (hydrogen sulfide, sulfides, disulfides, elemental sulfur)
Nitrogen less than 1% (basic compounds with amine groups)
Oxygen less than 1% (found in organic compounds such as carbon dioxide, phenols,
ketones, carboxylic acids)
Metals less than 1% (nickel, iron, vanadium, copper, arsenic)
Salts less than 1% (sodium chloride, magnesium chloride, calcium chloride)
There are two things that make hydrocarbons exciting to chemists:
• Hydrocarbons contain a lot of energy. Many of the things derived from crude oil like gasoline,
diesel fuel, paraffin wax and so on take advantage of this energy.
• Hydrocarbons can take on many different forms. The smallest hydrocarbon is methane CH4), which is a gas that is a lighter than air. Longer chains with 5 or more carbons are liquids. Very long chains are solids like wax or tar. By chemically cross-linking hydrocarbon chains you can get everything from synthetic rubber to nylon to the plastic in tupperware. Hydrocarbon chains are very versatile.
The Major Classes Of Hydrocarbons In Crude Oils Include:
• Paraffins general formula: CnH2n+2 (n is a whole number, usually from 1 to 20) straight- or branched-chain molecules can be gasses or liquids at room temperature depending upon the molecule. examples: methane, ethane, propane, butane, isobutane, pentane, hexane.
• Aromatics general formula: C6H5 – Y (Y is a longer, straight molecule that connects to the
benzene ring) ringed structures with one or more rings contain six carbon atoms, with alternating double and single bonds between the carbons typically liquids examples: benzene,
naphthalene.
• Napthenes or Cycloalkanes general formula: CnH2n (n is a whole number usually from 1 to 20)
ringed structures with one or more rings contain only single bonds between the carbon atoms
typically liquids at room temperature examples: cyclohexane, methyl cyclopentane.
• Other hydrocarbons Alkenes general formula: CnH2n (n is a whole number, usually from 1 to 20)
linear or branched chain molecules containing one carbon-carbon double-bond can be liquid or gas examples: ethylene, butene, isobutene Dienes and Alkynes general formula: CnH2n-2 (n is a whole number, usually from 1 to 20) linear or branched chain molecules containing two carbon-carbon double-bonds can be liquid or gas; Examples: acetylene, butadienes
Fractional Distillation Column
The oil refining process starts with a fractional distillation.
The problem with crude oil is that it contains hundreds of different types of hydrocarbons all
mixed together. You have to separate the different types of hydrocarbons to have anything useful.
Fortunately there is an easy way to separate things, and this is what oil refining is all about. Different hydrocarbon chain lengths all have progressively higher boiling points, so they can all be separated by distillation. This is what happens in an oil refinery. In one part of the process, crude oil is heated and the different chains are pulled out by their vaporization
temperatures. Each different chain length has a different property that makes it useful in a
different way. To understand the diversity contained in crude oil, and to understand why
refining crude oil is so important in our society, look through the following list of products
that come from crude oil:
Petroleum gas – used for heating, cooking, making plastics
• Small alkanes (1 to 4 carbon atoms)
• Commonly known by the names methane, ethane, propane, butane
• Boiling range = less than 104 degrees Fahrenheit / 40 degrees Celsius
• Often liquefied under pressure to create LPG (liquefied petroleum gas)
Naphtha or Ligroin – intermediate that will be further processed to make gasoline
• Mix of 5 to 9 carbon atom alkanes
• Boiling range = 140 to 212 degrees Fahrenheit / 60 to 100 degrees Celsius
Gasoline – motor fuel
• Liquid
• Mix of alkanes and cycloalkanes (5 to 12 carbon atoms)
• Boiling range = 104 to 401 degrees Fahrenheit / 40 to 205 degrees Celsius
Kerosene – fuel for jet engines and tractors; starting material for making other products
• Liquid
• Mix of alkanes (10 to 18 carbons) and aromatics
• Boiling range = 350 to 617 degrees Fahrenheit / 175 to 325 degrees Celsius
Gas oil or Diesel distillate – used for diesel fuel and heating oil; starting material for
making other products
• Liquid
• Alkanes containing 12 or more carbon atoms
• Boiling range = 482 to 662 degrees Fahrenheit / 250 to 350 degrees Celsius
Lubricating oil – used for motor oil, grease, other lubricants
• Liquid
• Long chain (20 to 50 carbon atoms) alkanes, cycloalkanes, aromatics
• Boiling range = 572 to 700 degrees Fahrenheit / 300 to 370 degrees Celsius
Heavy gas or Fuel oil – used for industrial fuel; starting material for making other products
• Liquid
• Long chain (20 to 70 carbon atoms) alkanes, cycloalkanes, aromatics
• Boiling range = 700 to 1112 degrees Fahrenheit / 370 to 600 degrees Celsius
Residuals – coke, asphalt, tar, waxes; starting material for making other products
• Solid
• Multiple-ringed compounds with 70 or more carbon atoms
• boiling range = greater than 1112 degrees Fahrenheit / 600 degrees Celsius
You may have noticed that all of these products have different sizes and boiling ranges. Chemists take advantage of these properties when refining oil. Oil Refinery
The Refining Process
As mentioned previously, a barrel of crude oil has a mixture of all sorts of hydrocarbons in it.
Oil refining separates everything into useful substances. Chemists use the following steps:
1. The oldest and most common way to separate things into various components (called
fractions), is to do it using the differences in boiling temperature. This process is
called fractional distillation. You basically heat crude oil up, let it vaporize and
then condense the vapor.
2. Newer techniques use Chemical processing on some of the fractions to make others, in a
process called conversion. Chemical processing, for example, can break longer chains
into shorter ones. This allows a refinery to turn diesel fuel into gasoline depending
on the demand for gasoline.
3. Refineries must treat the fractions to remove impurities.
4. Refineries combine the various fractions (processed, unprocessed) into mixtures to make
desired products. For example, different mixtures of chains can create gasolines with
different octane ratings.
The products are stored on-site until they can be delivered to various markets such as gas
stations, airports and chemical plants. In addition to making the oil-based products,
refineries must also treat the wastes involved in the processes to minimize air and water
pollution.
Fractional Distillation
The various components of crude oil have different sizes, weights and boiling temperatures; so,
the first step is to separate these components. Because they have different boiling temperatures,
they can be separated easily by a process called fractional distillation. The steps of fractional
distillation are as follows:
1. You heat the mixture of two or more substances (liquids) with different boiling points to a high temperature. Heating is usually done with high pressure steam to temperatures of about 1112 degrees Fahrenheit / 600 degrees Celsius.
2. The mixture boils, forming vapor (gases); most substances go into the vapor phase.
3. The vapor enters the bottom of a long column (fractional distillation column) that is filled with trays or plates. The trays have many holes or bubble caps (like a loosened cap on a soda bottle) in them to allow the vapor to pass through. They increase the contact time between the vapor and the liquids in the column and help to collect liquids that form at various heights in the column. There is a temperature difference across
the column (hot at the bottom, cool at the top).
4. The vapor rises in the column.
5. As the vapor rises through the trays in the column, it cools.
6. When a substance in the vapor reaches a height where the temperature of the column is equal to that substance’s boiling point, it will condense to form a liquid. (The substance with the lowest boiling point will condense at the highest point in the column; substances with higher boiling points will condense lower in the column.).
7. The trays collect the various liquid fractions.
8. The collected liquid fractions may pass to condensers, which cool them further, and then go to storage tanks, or they may go to other areas for further chemical processing
Fractional distillation is useful for separating a mixture of substances with narrow differences
in boiling points, and is the most important step in the refining process.
The oil refining process starts with a fractional distillation.
Very few components come out of the fractional distillation ready for market. Many of them must
be chemically processed to make other fractions. For example, only 40% of distilled crude oil is
gasoline; however, gasoline is one of the major products made by oil companies. Rather than
continually distilling large quantities of crude oil, oil companies chemically process some
other fractions from the distillation to make gasoline; this processing increases the yield
of gasoline from each barrel of crude oil.
Chemically processing one fraction into another.
Chemical Processing
You can change one fraction into another by one of three methods:
• Breaking large hydrocarbons into smaller pieces (cracking)
• Combining smaller pieces to make larger ones (unification)
• Rearranging various pieces to make desired hydrocarbons (alteration)
Cracking takes large hydrocarbons and breaks them into smaller ones.
There are several types of cracking:
Thermal – you heat large hydrocarbons at high temperatures (sometimes high pressures as
well) until they break apart.
Steam – high temperature steam (1500 degrees Fahrenheit / 816 degrees Celsius) is used to break
ethane, butane and naptha into ethylene and benzene, which are used to manufacture chemicals.
Visbreaking – residual from the distillation tower is heated (900 degrees Fahrenheit / 482
degrees Celsius), cooled with gas oil and rapidly burned (flashed) in a distillation tower.
This process reduces the viscosity of heavy weight oils and produces tar.
Coking – residual from the distillation tower is heated to temperatures above 900 degrees
Fahrenheit / 482 degrees Celsius until it cracks into heavy oil, gasoline and naphtha. When the
process is done, a heavy, almost pure carbon residue is left (coke); the coke is cleaned from
the cokers and sold.
Industrial Cracking
Catalysts used in catalytic cracking or reforming
• Catalytic – uses a catalyst to speed up the cracking reaction. Catalysts include zeolite,
aluminum hydrosilicate, bauxite and silica-alumina.
Fluid catalytic cracking – a hot, fluid catalyst (1000 degrees Fahrenheit / 538 degrees Celsius)
cracks heavy gas oil into diesel oils and gasoline.
Hydrocracking – similar to fluid catalytic cracking, but uses a different catalyst, lower
temperatures, higher pressure, and hydrogen gas. It takes heavy oil and cracks it into gasoline
and kerosene (jet fuel).
After various hydrocarbons are cracked into smaller hydrocarbons, the products go through
another fractional distillation to separate them.
Unification
Sometimes, you need to combine smaller hydrocarbons to make larger ones — this process is called unification. The major unification process is called catalytic reforming and uses a
catalyst (platinum, platinum-rhenium mix) to combine low weight naphtha into aromatics, which are used in making chemicals and in blending gasoline. A significant by-product of this reaction is hydrogen gas, which is then either used for hydrocracking or sold.
Alteration
Sometimes, the structures of molecules in one fraction are rearranged to produce another.
Commonly, this is done using a process called alkylation. In alkylation, low molecular weight
compounds, such as propylene and butylene, are mixed in the presence of a catalyst such as
hydrofluoric acid or sulfuric acid (a by-product from removing impurities from many oil products).
The products of alkylation are high octane hydrocarbons, which are used in gasoline blends to
reduce knocking.
Now that we have seen how various fractions are changed, we will discuss the how the fractions
are treated and blended to make commercial products.
Treating and Blending the Fractions
Distillated and chemically processed fractions are treated to remove impurities, such as organic
compounds containing sulfur, nitrogen, oxygen, water, dissolved metals and inorganic salts.
Treating is usually done by passing the fractions through the following:
• A column of sulfuric acid – removes unsaturated hydrocarbons (those with carbon-carbon
double-bonds), nitrogen compounds, oxygen compounds and residual solids (tars, asphalt)
• An absorption column filled with drying agents to remove water
• Sulfur treatment and hydrogen-sulfide scrubbers to remove sulfur and sulfur compounds
After the fractions have been treated, they are cooled and then blended together to make various
products, such as:
• Gasoline of various grades, with or without additives
• Lubricating oils of various weights and grades (e.g. 10W-40, 5W-30)
• Kerosene of various grades
• Jet fuel
• Diesel fuel
• Heating oil
• Chemicals of various grades for making plastics and other polymers
ListFree.org: Embedded data.