Even further fixes. Nothing can be trusted apparently.
← Older revision
Revision as of 14:47, 2 May 2014
(2 intermediate revisions by one user not shown)
Line 2:
Line 2:
| image = [[File:Pcd_v2_front.jpg|250px]]
| image = [[File:Pcd_v2_front.jpg|250px]]
| manufacturer = [http://www.linksprite.com/ Linksprite]
| manufacturer = [http://www.linksprite.com/ Linksprite]
−
| dimensions = 125''mm'' x 52''mm''
+
| dimensions = 125''mm'' x 52
''mm'' x height
''mm''
−
| release_date =
February
2013
+
| release_date =
September
2013
−
| website = [http://www.pcduino.com/
features
/ Product Page]
+
| website = [http://www.pcduino.com/
pcduino-v2
/ Product Page]
| soc = [[A10]] @ 1Ghz
| soc = [[A10]] @ 1Ghz
−
| dram = 1GiB DDR3 @
480MHz
+
| dram = 1GiB DDR3 @
???MHz
−
| nand =
2GB
+
| nand =
2/4GB
| power = DC 5V @ 2A
| power = DC 5V @ 2A
| video = HDMI (Type A - full)
| video = HDMI (Type A - full)
−
| audio =
3.5mm headphone plug, 3.5mm microphone plug,
HDMI
, SPDIF
+
| audio = HDMI
−
| network = 10/100Mbps Ethernet (+
1 RTL8188CUS on v2
)
+
| network =
WiFi 802.11bgn (Realtek RTL8188CUS),
10/100Mbps Ethernet (
IC
+
IP101A
)
−
| storage = µSD
, SATA
+
| storage = µSD
−
| usb =
2
USB2.0 Host, 1 USB2.0 OTG
(for V2, it's 1 PHY/1 OTG)
+
| usb =
1
USB2.0 Host, 1 USB2.0 OTG
| headers = UART, Arduino Compatible Headers
| headers = UART, Arduino Compatible Headers
}}
}}
Line 19:
Line 19:
{{Remove|This page needs to be properly filled according to the [[New_Device_howto |New Device Howto]] and the [[New_Device_page|New Device Page guide]].}}
{{Remove|This page needs to be properly filled according to the [[New_Device_howto |New Device Howto]] and the [[New_Device_page|New Device Page guide]].}}
−
The pcDuino is an [[A10]] based development board with [http://en.wikipedia.org/wiki/Arduino Arduino] compatible headers.
+
The pcDuino
V2
is an [[A10]] based development board with [http://en.wikipedia.org/wiki/Arduino Arduino] compatible headers.
= Identification =
= Identification =
−
This is a development
board,
can be directly bought from the manufacturer or various vendors. Look for "pcDuino" or
"pcDuino V2"
on the back of the board.
+
On the back of the
board,
it helpfully says
"pcDuino V2".
−
+
−
There are two closely-tied versions of this board:
+
−
+
−
* pcDuino v1 - 2 USB PHY
+
−
* pcDuino v2 - 1 USB PHY + 1 802
.
11n NIC connected via USB
+
= Sunxi support =
= Sunxi support =
Line 34:
Line 29:
== Current status ==
== Current status ==
−
Supported
.
+
No patches have been submitted for this specific board
.
== Images ==
== Images ==
Line 41:
Line 36:
== BSP ==
== BSP ==
−
−
* pcDuino v1: http://www.pcduino.com/download/
−
* pcDuino v2: http://www.pcduino.com/images-for-pcduino-v2/
== Manual build ==
== Manual build ==
−
* For building u-boot, use the "
pcDuino
" target.
+
* For building u-boot, use the "
{{Remove|MANUFACTURER_DEVICE}}
" target.
−
* The .fex file can be found in sunxi-boards as [https://github.com/linux-sunxi/sunxi-boards/blob/master/sys_config/
a10
/
pcduino
.fex
pcduino
.fex]
+
* The .fex file can be found in sunxi-boards as [https://github.com/linux-sunxi/sunxi-boards/blob/master/sys_config/
SOC
/
MANUFACTURER_DEVICE
.fex
MANUFACTURER_DEVICE
.fex]
Everything else is the same as the [[manual build howto]].
Everything else is the same as the [[manual build howto]].
Line 60:
Line 52:
= Adding a serial port =
= Adding a serial port =
−
Look for
the
3-pin group near the wifi module
,
called
UART.
+
[[File:device_uart.jpg|thumb|240px|{{Remove|DEVICE}} UART pads]]
+
+
There is 2.54mm pitch header next to
the
Wifi Module
,
labelled "UART". All you need to do is connect some jumper wires according to our [[UART|
UART
howto]]
.
= Pictures =
= Pictures =
Line 71:
Line 65:
= Also known as =
= Also known as =
−
No known re-badged devices as
of
05/02/2014
.
+
This type
of
device has no rebadges
.
= See also =
= See also =
−
+
* [[LinkSprite pcDuino]]
+
* [[LinkSprite pcDuino V3]]
* [https://s3.amazonaws.com/pcduino/User+Guide/pcDuino+User+Guide+Rev.+0.4.pdf User Guide.]
* [https://s3.amazonaws.com/pcduino/User+Guide/pcDuino+User+Guide+Rev.+0.4.pdf User Guide.]
* [https://s3.amazonaws.com/pcduino/Hardware/PC+Duino_V01-20130128.pdf Schematics.]
* [https://s3.amazonaws.com/pcduino/Hardware/PC+Duino_V01-20130128.pdf Schematics.]
Line 81:
Line 76:
[[Category:A10 Boards]]
[[Category:A10 Boards]]
−
[[Category:Devices with SATA port]]
[[Category:Devices with Ethernet port]]
[[Category:Devices with Ethernet port]]
[[Category:NDH_TODO]]
[[Category:NDH_TODO]]