2016-02-10

Circular bolster cushions look attractive on most types of furniture and make a good visual contrast against the more usual rectangular cushions. This shape of cushion works particularly well with striped, check and tartan cloth, especially when a contrasting tassel, ribbon how or pompom is used as a trim.

A box cushion adds comfort and style to a sofa. This cushion has been made by tie dyeing individual patches of contrasting fabric then sewing them together. A box cushion adds comfort and style to a sofa. This cushion has been made by tie dyeing individual patches of contrasting fabric then sewing them together.

HOW TO SEW A BOX CUSHION

Cut out the fabric then cut the hack gussetin half lengthways and place together with the right sides facing. Pin and stitch the seam 12 min/1/2 in from the raw edges, leaving an opening for the zip (zipper).Press the scam open.

Pin and tack (baste) the zip in position along the opening, as shown, allowing the fabric to meet centrally over the zip teeth. Stitch the zip in place using a zip foot on the machine.

With the right sides facing, join the four gusset pieces together along the short ends, taking a 12 min/1/2 in seam allowance and leaving 12 mm/1/2 in unstitched at each end of the seams. Press the seams open.

With the right sides facing, pin and stitch the top edge of one gusset section to one edge of the top cover piece, taking a12 mm/1/2 in seam allowance. At the gusset seam, leave the needle in the fabric, raise the machine foot and pivot the fabric so the next section of gusset aligns with the next side of the top cover piece. Continue pinning and stitching each section around the top in this way. Open the zip, then repeat the procedure to attach the bottom cover piece to the remaining side of the gusset. Trim away the surplus cloth at the corners and then turn the cover right side out.

HOW TO MAKE A BOLSTER CUSHION

Cut out the fabric then pin and stitch the length of the bolster cover with a French seam. Turn right side out and press. Turn under is double 12 mm/t/’ in hem at each end of the tube. Pin and tack (baste) the hem in place using a contrasting thread.

Stitch along the hems, keeping the stitching close to the inner folds. Remove the tacking (basting) stitches and press thoroughly.

Using double thread run a row of gathering stitches along each end of the tube, close to the outer fold of the hem, leaving a long thread end. Insert the holster pad in the tube, then tighten the gathering threads to close the cover. Secure the thread ends, then cover the small hole left at each end by attaching a furnishing tassel, ribbon how or a button.

MAKING TASSELS

There are a great variety of tassels available in shops to be attached to the corners of cushions or on the ends of a bolster. The colors, shapes, sizes and designs are infinitesimal, but if you want something a bit more tailor made, create your own.

Cut out two pieces of cardboard to the length of your finished tassel and 10 cm/ 4 in wide. Place them together. Put .30 cm /12 in of your yarn to one side and then wind as much of the rest around the card from top to bottom until there is sufficient for the type of tassel you are making. The more you wind on, the fuller will be the result.

Stitch along the hems, keeping the stitching close to the inner folds. Remove the tacking (basting) stitches and press thoroughly. Thread the set aside yam through a needle and then pass the needle through the top of the wound yarn and tie at the top. Repeat several times so that you are left with a strong loop at the top of the tassel, it will be attached later to the item you are dressing up. Holding the yarn firmly in one hand, cut through the yarn at the bottom between the two pieces of cardboard then release the cardboard and then bind the tassel as near as possible to the top to ensure that the head remains firm. To neaten, comb out the yarn using your fingertips and then give the whole tassel a good trim.

FRENCH SEAMS

A French seam encloses the raw edges of fabric and prevents them from fraying. It is worked in two stages: first stitch with the wrong sides facing (top). Trim the raw edges close to the first row of stitching then stitch with the right sides facing (above).

CALCULATING FABRIC

Box cushion: Measure the length and width of the top of the pad and then add 12 mm/1/2 in all around for seam allowances, two pieces of fabric this size are needed, one for the top and one for the bottom of the cover. The gusset is made from four pieces of fabric joined together. Measure the depth and width of the pad and add12 mm/1/2 in all around for seam allowances. Cut out three pieces of fabric to this size. Add an extra 2.5 cm/1 in to the depth of the fourth piece for the zip (zipper) seam in the gusset.

Bolster cushion: Measure the bolster from the centre point of one end, along its length and around to the centre point of the opposite end, adding a total of 5 cm/2 in for hem allowances. To calculate the width, measure the circumference of the pad and add an extra 2.5 cm/1 in for seam allowances. Cut one large piece to fit these dimensions.

Related posts:

How to Make Couch Cushion Covers

Easy Cushion Embellishments

Cushion Materials

How to Make Bed Linen

How to Make a Table Cloth

How to Use a Sewing Machine

Hand Sewing

How to Make Curtains

How to Make Roman Blinds

How to Decorate a Table

Show more