Bonjour à tous,
Sur mon serveur dédié dans mes logs j'ai vue apparaitre ceci
Code :
---------
WARNING: Kernel Errors Present
grsec: From xxx.xxx.xxx.xxx: Invalid alignment/Bus error occurred at 0000 ...: 2 Time(s)
---------
Je me suis donc dit qu'il fallait que je vérifie peut être la santé du disque dur en lançant un smartctl, sauf qu'au vue du résultat je ne sais pas dire si au final il y a réellement un problème ou non...
Code :
---------
smartctl -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10 family
Device Model: ST3250310AS
Serial Number: 6RY4PAVQ
Firmware Version: 3.AAC
User Capacity: 250 059 350 016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Mar 19 17:56:04 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.
SCT capabilities: (0x0001) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 103 086 006 Pre-fail Always - 50530175
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 57
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 090 060 030 Pre-fail Always - 980877251
9 Power_On_Hours 0x0032 051 051 000 Old_age Always - 43700
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 57
187 Reported_Uncorrect 0x0032 073 073 000 Old_age Always - 27
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 068 046 045 Old_age Always - 32 (Lifetime Min/Max 28/52)
194 Temperature_Celsius 0x0022 032 054 000 Old_age Always - 32 (0 18 0 0)
195 Hardware_ECC_Recovered 0x001a 058 049 000 Old_age Always - 103096564
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 2
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 2
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 27 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 27 occurred at disk power-on lifetime: 37448 hours (1560 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 50 9a 80 e0 Error: UNC at LBA = 0x00809a50 = 8428112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 50 9a 80 e0 00 07:44:18.896 READ DMA
27 00 00 00 00 00 e0 00 07:44:18.896 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 07:44:18.889 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 07:44:15.255 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 07:44:15.255 READ NATIVE MAX ADDRESS EXT
Error 26 occurred at disk power-on lifetime: 37448 hours (1560 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 50 9a 80 e0 Error: UNC at LBA = 0x00809a50 = 8428112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 50 9a 80 e0 00 07:44:18.896 READ DMA
27 00 00 00 00 00 e0 00 07:44:18.896 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 07:44:18.889 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 07:44:15.255 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 07:44:15.255 READ NATIVE MAX ADDRESS EXT
Error 25 occurred at disk power-on lifetime: 37448 hours (1560 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 50 9a 80 e0 Error: UNC at LBA = 0x00809a50 = 8428112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 50 9a 80 e0 00 07:44:07.904 READ DMA
27 00 00 00 00 00 e0 00 07:44:07.904 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 07:44:07.888 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 07:44:15.255 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 07:44:15.255 READ NATIVE MAX ADDRESS EXT
Error 24 occurred at disk power-on lifetime: 37448 hours (1560 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 50 9a 80 e0 Error: UNC at LBA = 0x00809a50 = 8428112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 50 9a 80 e0 00 07:44:07.904 READ DMA
27 00 00 00 00 00 e0 00 07:44:07.904 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 07:44:07.888 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 07:44:07.872 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 07:44:07.872 READ NATIVE MAX ADDRESS EXT
Error 23 occurred at disk power-on lifetime: 37448 hours (1560 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 50 9a 80 e0 Error: UNC at LBA = 0x00809a50 = 8428112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 50 9a 80 e0 00 07:44:07.904 READ DMA
27 00 00 00 00 00 e0 00 07:44:07.904 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 07:44:07.888 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 07:44:07.872 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 07:44:07.872 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 24779 -
# 2 Short offline Completed without error 00% 16066 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
---------
Je vois bien les erreurs mais est-ce que c'est simplement du au fait qu'il tourne depuis longtemps...
---Citation---
Error 27 occurred at disk power-on lifetime: 37448 hours (1560 days + 8 hours)
---Fin de la citation---
Merci de votre aide
a+