15-Channel Modular Reconfigurable Data Logging System
Measure and Record Current, Voltage, Power, Pressure and more
Battery Operation or AC Power Available
12 Volt Excitation for Sensors
Requires 1 FlexSmart Module, Sensors and HoboWare Pro Software
The HOBO Energy Logger is a 15 channel indoor data logger with the ability to measure and record almost any environmental condition using the required FlexSmart Modules.
The Energy Logger allows you to measure and record:
>> AC/DC Current, AC/DC Voltage,4-20mA
>> Power, Kilowatts, Kilowatt Hours
>> Pressure (Differential, Barometric, Gauge)
>> Pulse and Analog Inputs
>> Wind, Rain, Light, Carbon Dioxide
>> Temperature and Relative Humidity
>> and more...
Included with each HOBO Energy Logger
>> User Guide
>> (8) 1.5V Batteries
>> Miniature Slotted Screwdriver
>> Blank Label
>> Rubber Feet
HOBO Energy Logger Features
Flexible Expansion for up to 3 FlexSmart Modules and 6 Smart Sensors
Automatic Detection of Smart Sensors by logger
Digital Connection of Smart Sensors to logger for Accurate, Reliable Data Collection and Storage
Multiple Internal and External Power Sources Available for Long-Term Usage
User-Configurable Sensor Excitation Power and Warmup using Analog Module (#S-FS-CVIA)
Optional Data Shuttle Available to Collect Data in Remote Areas
Requires HOBOware Software and USB Kit (PC and MAC Versions)
HOBO Energy Logger Specifications
Data Storage Capacity
512K Maximum Storage - Number of Samples Dependant on External Sensors and FlexSmart Modules
Sampling Rate
1 Second to 18 Hours
(2-Second Minimum for #S-FS-TRMSA operation)
Sensor Excitation
12 Volts DC at 200 mA total, with User-Programmable Warmup Time on a per-Channel Basis
Logging Modes
Immediate, Timed Delay, or Push-Button Start Options
Memory Modes
Stop When Full; Wrap When Full
LED Indicators
Green: Logging or Standby
Red: Low Battery, Storage or Sensor Fail
Sensor Inputs
3 FlexSmart multi-Channel Modules and up to 6 Smart Sensors
Sensor Connectors
6 RJ-12 Smart Sensor Jacks and 3 FlexSmart Module Slots
Communications Type
RS-232 Serial via 3.5mm Serial Port or/and 9-pin D-Sub Connector
Communications Mode
Current Readings while Logging; Read Out While Logging; Read Out When Stopped
Operating Range
Alkaline Battery: -20C to 50C (-4F to 122F)
Lithium Battery: -40C to 60C (-40F to 140F)
Battery Life
1 Year Typical Use ( up to 75 mA excitation with 10-minute or longer logging interval and 1-second warmup-time)
Battery
AA Alkaline Batteries (Included)
External Power
13.6 VDC Regulated AC Wall Adapter Connector
9-12 VDC Regulated Wall Adapter (Remove Batteries)
Time Accuracy
0 to 2 Seconds for first data point and ±5 Seconds per Week at 25°C (77°F)
Standards Compliance
CE
Weight
435g (15.23 oz) with Batteries
Dimensions
15.6cm x 8.4cm x 4.6cm (6.13" x 3.31" x 1.81")
NOTE: 1 FlexSmart Analog Module or TRMS Module is Required
The FlexSmart Modules are snap-in signal conditioning units that convert signals from nearly any type of sensor.
FlexSmart Analog (CVIA) Module (#S-FS-CVIA)
>> Flexible DC Signal-Conditioning Module
>> Accepts 2 Channels
>> Input Protection and Signal Filtering
>> Excitation Power to wide range of sensors
Input Channels
2, Single-Ended
Field Wiring
2 or 3 Wire Screw terminals on Detachable Terminal Block, 16 to 24 Gauge (AWG)
Input Range
User-Configurable: 0 to 20 mA DC; 0 to 20 Volts DC
(Suitable for 2.5, 5 and 10 Volt Sensors
Input Voltage Range
0 to 24 Volts DC
Input Current Range
0 to 24 mA DC
Minimum Current Source Impedance
Accuracy
± 0.25% of FSR from 50 mV to FSR
ADC Resolution
12 Bits
Standards Compliance
CE
Power Requirements
+3.3 Volts @ 3mA Active, 6 uA Sleep
TRMS (TRMSA) Module (#S-FS-TRMSA)
>> 2 Channel Input Measurement Module
>> Compatible with Industry-standard Current and Potential Transformers
>> Input Range of 512 mV RMS Full Scale
>> Output Range of 333 mV RMS Full Scale
Input Channels
2
Field Wiring
2 Wire Screw Terminals
Range
5mV to 512mV
(Compatible with 333mV FS Output Sensors)
Maximum Input
± 1V
Minimum Input
5mV
Accuracy
± 0.3% of Reading; ± 0.5% FSR
Resolution
15 Bits
Standards Compliance
CE
Part Number: H22-001
Required:
>> FlexSmart Module
>> Smart Sensors
>> HOBOware™ Pro Software
Description
Part Number
HOBO U30 Shuttle
U-DT-2
USB Serial Adapter
CABLE-USB232
Mount Feet Kit
A-H22-MOUNT-1
Din Mounting Feet Kit
A-H22-DINMOUNT-1
H22 Onset Energy Logger Replacement Kit
A-H22-SPARES-1
AA Batteries (Lithium) 4 Pack
HWSB-LI
AC Power Adapter
P-AC-1
1 to 2 Sensor Communication Adapter
S-ADAPT
Applications:
The Energy Logger allows you to monitor and record:
>> HVAC and HVAR
>> Energy Metering and Power Monitoring
>> Facility Monitoring
>> Industrial Machinery Monitoring and Motor Start-Up Analysis
>> Temperature and Humidity Monitoring
>> and alot more ....