I’ve recently received a kit based on Orange Pi mini 2 development board powered by Allwinner H3 quad core processor, but contrary to most other devices or boards I reviewed, this one what sent to me by one of my reader (thanks Jon!) as for various reasons he did not need to get it shipped to him. Today, I’ll start by showing off the kit, I received, before showing how to install a Debian, and finally try to build my own Linux image. The instructions will work for all Orange Pi Allwinner H3 boards, including Orange Pi 2, Orange Pi Plus, and the recently launched Orange Pi PC, which has been rather popular thanks to its low $15 price tag.
Orange Pi mini 2 Board Kit and CSI Camera
This is what I got in the package…
Click to Enlarge
The board with a regulatory compliance and safety information sheet, as well as a 5V/2A power supply, that was bought as part of a kit for $28.90 on Aliexpress. Bear in mind that although Orange Pi boards feature a micro USB OTG port, AFAIK none of them can be power via the micro USB connector, and instead you need to make you have a 5V power adapter with the right barrel size, meaning you can re-use your old smartphone’s charger like you would do with a Raspberry Pi. Shenzhen Xunlong normally offers various kits including power supply and/or acrylic case on their Aliexpress store.
I’ve taken the board out of its anti-static bag, and taken some close up pictures.
Top of Orange Pi Mini 2 Board (Click to Enlarge)
Bottom of Orange Pi Mini 2 Board (Click to Enlarge)
So my board does not include flash, nor a WiFi module (located on the top left corner on the top), which I’ll connect the board via Ethernet, and boot from a micro SD card.
Then I noticed a tiny plastic bag had fallen on my desk… oh!!! a camera…
Orange Pi Camera
The cable reads SH-2035-IPLAY, and it must the be the $5.90 camera sold on Aliexpress by Xunlong Software, Orange Pi board makers, although the picture differs a bit. So I looked for some documentation about the camera on Orange Pi website, and I found… nothing… Until I looked into the forums, and found somebody managed to make it work after many efforts, as the firmware images were not setup for the camera, and the driver was also missing. I initially intended to try out the camera in this getting started guide, but it will have to be a separate post.
Installing and Setting Up Linux
Orange Pi Allwinner H3 boards support both Android and Ubuntu, but most people buying such development board are likely to prefer running a Linux distribution, and I’ve already tested Android on Allwinner H3 when I reviewed Zidoo X1, so I decided to focus on Linux in this getting started guide. Orange Pi 2 boards and Zidoo X1 are pretty similar hardware platform, and I’ve already installed Orange Pi 2 Lubuntu 14.04 on Zidoo X1 downloaded from Orange Pi Downloads page, and vice versa, Zidoo X1 Android image has also been tested on Orange Pi 2. And in both cases the images run fine, although with some caveats such as WiFi not working with Linux on Zidoo X1.
However, I’ve been recommended to use Linux images released by Loboris forum member instead, so that’s what I’ve done, and among the various Ubuntu, Lubuntu, and Debian images available, I’ve decided to go with Debian 8 Jessie + XFCE image (OrangePI_Jessie_Xfce.img.xz), and you can download the images from Mega or Google Drive. Minimal images without desktop environment for headless operation are also available.
You’ll need a Linux or Windows PC, and a micro SD card to install the Linux image.
These are the steps I followed to install Debian on the micro SD card from a Ubuntu 14.04 computer:
Install dependencies:
Uncompress the firmware:
Locate your micro SD card with lsblk (I used a 16GB Class 10 micro SD card):
Flash the image with dd:
Note: If you are using Windows, use Win32DiskImager to flash the image to the micro SD card instead of going through the first 4 steps shown above.
Remove the micro SD card, and reinsert it again in your computer, it should automount two partitions in the SD card: linux and BOOT.
You’ll want to select the BOOT partitions, where you’ll find the kernel “uImage_OPI-2” for Orange Pi 2 and Pi PC boards, and “uImage_OPI-PLUS” for Orange Pi Plus boards. uImage in the partition was already uImage_OPi-2 for my board, but to be on the safe side, you can copy the kernel image to uImage. Finally, you’ll also need to select one of the scrip.bin file to match the board and resolution you wish to use. This is what I did in a terminal window for my Orange Pi mini 2 board, but you can also use the desktop to do so in Linux or Windows:
Done! The micro SD card is now ready.
You can insert it into your board, and connect the power. After a few seconds you should start seeing the kernel log on the screen, and a little later the login screen.
Type the user name “orangepi” and the password “orangepi” to login. There’s still one last step to complete the setup. Open a terminal window:
The installation is now complete, have fun! The whole process what quite straightforward thanks to clear instructions provided by Lobrosis.
Running Debian 8 on Orange Pi mini 2
I’ve quickly tested the image. Chromium is pre-installed, and the developer must be from Croatia, since Chromium will start google.hr by default. Web browsing is fine, but Adobe flash (libpepperflash) is not installed, Thai language is not supported, and Youtube videos are super slow and unwatchable in Chromium. Having said that, you can use SMPlayer to watch YouTube video perfectly fine… in windowed mode (as shown in the screenshot below), but if you go full screen the system can’t cope. I’ve also tried to play a 1080p H.264 video locally, but it won’t play smoothly at all. es2gears (installed with apt-get install mesa-utils-extra) runs, but es2_info reports the render is the software rasterizer.
Debian 8 running in Orange Pi mini 2 (Click for Original Size)
So the image does not support 2D/3D GPU acceleration nor hardware video decoding, but this was to be expected, and these two are usually time consuming to implement. If you need OpenGLES or hardware video decoding, you’ll need to use Android instead. The language issues and lack of Adobe flash support in Chromium should be easy to fix yourself by installing the needed software package such as libpepperflash. I had no problem accessing Internet using Ethernet, I just connected the cable and was good to go.
Here are some details about the image, as well as its memory and storage usage:
You’ll notice that the CPU frequency is set to 1.5GHz, instead of 1.2GHz in consumer devices like Zidoo X1, so if you plan to run the system at full speed for an extended period of time, e.g. to build the kernel, you may consider adding a heatsink and a fan to the board.
I’ve also connected a USB to TTL debug board to the 3-pin serial console header of the board, and captured the full boot log with minicom:
HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 672 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 001d1d1e
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 15067MB
[mmc]: vendor: Man 001d4144 Snr b4140ee4
[mmc]: product: SD
[mmc]: revision: 0.2
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000dc000.
sum=ede66ee7
src_sum=ede66ee7
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE
[ 0.345]e mode
U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology
[ 0.352]version: 1.1.0
normal mode
[ 0.360]pmbus: ready
not set main pmu id
axp_probe error
[ 0.375]PMU: pll1 1200 Mhz,PLL6=600 Mhz
AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[ 0.405]DRAM: 1 GiB
relocation Offset is: 35af9000
read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC: 0
[ 0.479][mmc]: mmc driver ver 2014-12-10 9:23:00
[ 0.484][mmc]: get sdc_phy_wipe fail.
[ 0.488][mmc]: get sdc0 sdc_erase fail.
[ 0.492][mmc]: get sdc_f_max fail,use default 50000000Hz
[ 0.497][mmc]: get sdc_ex_dly_used fail,use default dly
[ 0.503][mmc]: SUNXI SD/MMC: 0
[ 0.516][mmc]: *Try SD card 0*
[ 0.549][mmc]: CID 0x1d414453 0x44202020 0x2b4140e 0xe400d2dd
[ 0.554][mmc]: mmc clk 50000000
[ 0.558][mmc]: SD/MMC Card: 4bit, capacity: 15067MB
[ 0.563][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[ 0.568][mmc]: ***SD/MMC 0 init OK!!!***
[ 0.572][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[ 0.578][mmc]: secure_feature 0x0
[ 0.581][mmc]: secure_removal_type 0x0
[ 0.585]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
boot_disp.auto_hpd=1
auto hpd check has 0 times!
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
attched ok, mgr0device0, type=4, mode=4----
ready to set mode
[ 1.466]finally, output_type=0x4, output_mode=0x4, screen_id=0x0, disp_par4
fail to find part named env
Using default environment
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
[ 1.504][mmc]: MMC Device 2 not found
[ 1.508][mmc]: Can not find mmc dev
[ 1.511][mmc]: read first backup failed in fun sdmmc_secure_storage_read l9
sunxi_secstorage_read fail
get secure storage map err
the private part isn't exist
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
[disk_read_fs] no the partition
error: open bootlogo.bmp, maybe it is not exist
sunxi bmp info error : unable to open logo file bootlogo.bmp
[ 1.544]Hit any key to stop autoboot: 0
[ 4.807][mmc]: blkcnt should not be 0
[ 5.161][mmc]: blkcnt should not be 0
## Booting kernel from Legacy Image at 40007800 ...
Image Name: Linux-3.4.39
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8029560 Bytes = 7.7 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
[ 5.310][mmc]: MMC Device 2 not found
[ 5.314][mmc]: mmc not find,so not exit
[ 5.318]
Starting kernel ...
[sun8i_fixup]: From boot, get meminfo:
Start: 0x40000000
Size: 1024MB
ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1
ion_reserve_common: ion reserve: [0x70000000, 0x80000000]!
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.39 (boris@UbuntuMate) (gcc version 4.6.3 201205
[ 0.000000] Ignoring tag cmdline (using the default kernel command line)
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] cma: CMA: reserved 256 MiB at 70000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0d21900, node_mem_map c0dfd00
[ 0.000000] Normal zone: 1710 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 192850 pages, LIFO batch:31
[ 0.000000] HighMem zone: 594 pages used for memmap
[ 0.000000] HighMem zone: 66990 pages, LIFO batch:15
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c1713000 s11840 r8192 d12736 u32768
[ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa0
[ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcalt
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1024MB = 1024MB total
[ 0.000000] Memory: 761624k/761624k available, 286952k reserved, 8192K highmm
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc095ad7c (9548 kB)
[ 0.000000] .init : 0xc095b000 - 0xc0ca9e40 (3388 kB)
[ 0.000000] .data : 0xc0caa000 - 0xc0d24378 ( 489 kB)
[ 0.000000] .bss : 0xc0d24b2c - 0xc0dfcdf8 ( 865 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:544
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 1789s
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.39 (boris@UbuntuMate) (gcc version 4.6.3 201205
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructie
[ 0.000000] Machine: sun8i
[ 0.000000] Ignoring tag cmdline (using the default kernel command line)
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] cma: CMA: reserved 256 MiB at 70000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0d21900, node_mem_map c0dfd00
[ 0.000000] Normal zone: 1710 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 192850 pages, LIFO batch:31
[ 0.000000] HighMem zone: 594 pages used for memmap
[ 0.000000] HighMem zone: 66990 pages, LIFO batch:15
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c1713000 s11840 r8192 d12736 u32768
[ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa0
[ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcalt
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1024MB = 1024MB total
[ 0.000000] Memory: 761624k/761624k available, 286952k reserved, 8192K highmm
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc095ad7c (9548 kB)
[ 0.000000] .init : 0xc095b000 - 0xc0ca9e40 (3388 kB)
[ 0.000000] .data : 0xc0caa000 - 0xc0d24378 ( 489 kB)
[ 0.000000] .bss : 0xc0d24b2c - 0xc0dfcdf8 ( 865 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:544
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 1789s
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.019915] Calibrating delay loop (skipped), value calculated using timer f)
[ 0.019970] pid_max: default: 32768 minimum: 301
[ 0.020237] Mount-cache hash table entries: 512
[ 0.021109] Initializing cgroup subsys cpuacct
[ 0.021139] Initializing cgroup subsys freezer
[ 0.021185] CPU: Testing write buffer coherency: ok
[ 0.021241] ftrace: allocating 25527 entries in 75 pages
[ 0.050249] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.050282] [sunxi_smp_prepare_cpus] enter
[ 0.050323] Setting up static identity map for 0x406b0b30 - 0x406b0b88
[ 0.051148] CPU1: Booted secondary processor
[ 0.051148] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.051278] CPU2: Booted secondary processor
[ 0.051278] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.051278] CPU3: Booted secondary processor
[ 0.051278] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.060172] Brought up 4 CPUs
[ 0.060255] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[ 0.060824] devtmpfs: initialized
[ 0.063132] wakeup src cnt is : 1.
[ 0.063152] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800
[ 0.063175] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpi0
[ 0.063200] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpi0
[ 0.063225] sunxi pm init
[ 0.063353] pinctrl core: initialized pinctrl subsystem
[ 0.073783] NET: Registered protocol family 16
[ 0.074436] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.074436] script_sysfs_init success
[ 0.074436] sunxi_dump_init success
[ 0.074436] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[ 0.074436] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[ 0.074436] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint.
[ 0.074436] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.074436] script config pll_video to 297 Mhz
[ 0.074448] script config pll_de to 864 Mhz
[ 0.074470] script config pll_ve to 402 Mhz
[ 0.074503] sunxi_default_clk_init
[ 0.074519] try to set pll6ahb1 to 200000000
[ 0.074546] try to set ahb clk source to pll6ahb1
[ 0.074564] set ahb clk source to pll6ahb1
[ 0.074583] try to set ahb1 to 200000000
[ 0.074602] try to set apb1 to 100000000
[ 0.074934] ===fe3o4==== sunxi_root_procfs_attach ret:0
[ 0.080214] bio: create slab at 0
[ 0.080363] [ARISC] :sunxi-arisc driver v1.04
[ 0.094759] [ARISC] :arisc version: [v0.1.34]
[ 0.171321] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
[ 0.180381] SCSI subsystem initialized
[ 0.180567] usbcore: registered new interface driver usbfs
[ 0.180645] usbcore: registered new interface driver hub
[ 0.180684] usbcore: registered new device driver usb
[ 0.180684] twi_chan_cfg()335 - [twi0] has no twi_regulator.
[ 0.180684] twi_chan_cfg()335 - [twi1] has no twi_regulator.
[ 0.180684] twi_chan_cfg()335 - [twi2] has no twi_regulator.
[ 0.180684] Linux video capture interface: v2.00
[ 0.180694] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.181165] Bluetooth: Core ver 2.16
[ 0.181213] NET: Registered protocol family 31
[ 0.181232] Bluetooth: HCI device and connection manager initialized
[ 0.181257] Bluetooth: HCI socket layer initialized
[ 0.181277] Bluetooth: L2CAP socket layer initialized
[ 0.181318] Bluetooth: SCO socket layer initialized
[ 0.181520] cfg80211: Calling CRDA to update world regulatory domain
[ 0.181599] Switching to clocksource arch_sys_counter
[ 0.192021] FS-Cache: Loaded
[ 0.192297] CacheFiles: Loaded
[ 0.201839] NET: Registered protocol family 2
[ 0.202107] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.202633] TCP established hash table entries: 131072 (order: 8, 1048576 by)
[ 0.204247] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.205040] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.205064] TCP: reno registered
[ 0.205084] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.205128] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.205407] NET: Registered protocol family 1
[ 0.205736] RPC: Registered named UNIX socket transport module.
[ 0.205764] RPC: Registered udp transport module.
[ 0.205782] RPC: Registered tcp transport module.
[ 0.205801] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.368203] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 countee
[ 0.368348] sunxi_reg_init enter
[ 0.369085] audit: initializing netlink socket (disabled)
[ 0.369143] type=2000 audit(0.360:1): initialized
[ 0.372253] highmem bounce pool size: 64 pages
[ 0.373421] Installing knfsd (copyright (C) 1996 [email protected]).
[ 0.374072] NTFS driver 2.1.30 [Flags: R/W].
[ 0.374195] fuse init (API version 7.18)
[ 0.374897] Btrfs loaded
[ 0.374932] msgmni has been set to 1471
[ 0.375932] io scheduler noop registered
[ 0.375956] io scheduler deadline registered
[ 0.376038] io scheduler cfq registered (default)
[ 0.376457] [DISP]disp_module_init
[ 0.376760] cmdline,disp=
[ 0.395144] [DISP] Fb_map_kernel_logo,line:925:Fb_map_kernel_logo failed!
[ 0.423097] Console: switching to colour frame buffer device 240x67
[ 0.451729] [DISP]disp_module_init finish
[ 0.452010] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[ 0.452161] sw_uart_get_devinfo()1503 - uart1 has no uart_regulator.
[ 0.452307] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
[ 0.452857] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 0.453003] sw_uart_pm()890 - uart0 clk is already enable
[ 0.453134] sw_console_setup()1233 - console setup baud 115200 parity n bitsn
[ 0.645126] console [ttyS0] enabled
[ 1.241849] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 1.242101] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[ 1.242570] sunxi_cmatest_init enter
[ 1.242602] sunxi_cmatest_init success
[ 1.246313] loop: module loaded
[ 1.423178] sunxi_spi_chan_cfg()1355 - [spi-0] has no spi_regulator.
[ 1.801619] sunxi_spi_chan_cfg()1355 - [spi-1] has no spi_regulator.
[ 1.946137] spi spi0: master is unqueued, this is deprecated
[ 1.958178] tun: Universal TUN/TAP device driver, 1.6
[ 1.969249] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.982383] PPP generic driver version 2.4.2
[ 1.992774] PPP BSD Compression module registered
[ 2.003514] PPP Deflate Compression module registered
[ 2.019959] PPP MPPE Compression module registered
[ 2.030960] NET: Registered protocol family 24
[ 2.041542] PPTP driver version 0.8.5
[ 2.051494] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.084578] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (Er
[ 2.099289] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus nu1
[ 2.113961] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[ 2.140045] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[ 2.152902] hub 1-0:1.0: USB hub found
[ 2.162783] hub 1-0:1.0: 1 port detected
[ 2.193163] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (Er
[ 2.207903] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus nu2
[ 2.222499] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
[ 2.250036] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
[ 2.262356] ehci_irq: highspeed device connect
[ 2.273153] hub 2-0:1.0: USB hub found
[ 2.283095] hub 2-0:1.0: 1 port detected
[ 2.293466] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.326090] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI)r
[ 2.340358] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus nu3
[ 2.354520] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
[ 2.424514] hub 3-0:1.0: USB hub found
[ 2.434351] hub 3-0:1.0: 1 port detected
[ 2.444637] Initializing USB Mass Storage driver...
[ 2.455772] usbcore: registered new interface driver usb-storage
[ 2.468086] USB Mass Storage support registered.
[ 2.478899] usbcore: registered new interface driver ums-alauda
[ 2.491303] usbcore: registered new interface driver ums-cypress
[ 2.503731] usbcore: registered new interface driver ums-datafab
[ 2.516035] usbcore: registered new interface driver ums_eneub6250
[ 2.528437] usbcore: registered new interface driver ums-freecom
[ 2.540632] usbcore: registered new interface driver ums-isd200
[ 2.552627] usbcore: registered new interface driver ums-jumpshot
[ 2.564770] usbcore: registered new interface driver ums-karma
[ 2.576541] usbcore: registered new interface driver ums-onetouch
[ 2.588539] usbcore: registered new interface driver ums-realtek
[ 2.600395] usbcore: registered new interface driver ums-sddr09
[ 2.610047] usb 2-1: new high-speed USB device number 2 using sunxi-ehci
[ 2.624731] usbcore: registered new interface driver ums-sddr55
[ 2.636556] usbcore: registered new interface driver ums-usbat
[ 2.648347] usbcore: registered new interface driver usbserial
[ 2.660012] usbserial: USB Serial Driver core
[ 2.670054] usbcore: registered new interface driver option
[ 2.681497] USB Serial support registered for GSM modem (1-port)
[ 2.693777] file system registered
[ 2.704175] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 2.717074] android_usb gadget: Number of LUNs=3
[ 2.727360] lun0: LUN: removable file: (no medium)
[ 2.737999] lun1: LUN: removable file: (no medium)
[ 2.748638] lun2: LUN: removable file: (no medium)
[ 2.759482] android_usb gadget: android_usb ready
[ 2.761132] hub 2-1:1.0: USB hub found
[ 2.761262] hub 2-1:1.0: 4 ports detected
[ 2.788628] uinput result 0 , vmouse_init
[ 2.798738] mousedev: PS/2 mouse device common for all mice
[ 2.810177] sunxikbd_init failed.
[ 2.818920] ls_fetch_sysconfig_para: type err device_used = 0.
[ 2.830685] =========script_get_err============
[ 2.840842] ltr_init: ls_fetch_sysconfig_para err.
[ 2.851696] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[ 2.864298] i2c /dev entries driver
[ 2.873568] IR RC5(x) protocol handler initialized
[ 2.884131] sunxi tsc version 0.1
[ 2.893053] tscdev_init: tsc driver is disabled
[ 2.903281] sunxi cedar version 0.1
[ 2.912363] [cedar]: install start!!!
[ 2.921661] [cedar]: install end!!!
[ 2.930579] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[ 2.942768] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->stf
[ 2.954115] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[ 2.971851] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[ 2.983253] timeout_to_interv, line 167
[ 2.992661] interv_to_timeout, line 189
[ 3.002019] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual tc
[ 3.016730] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-m
[ 3.031489] Bluetooth: HCI UART driver ver 2.2
[ 3.042139] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.109 2014-12-4 20:511
[ 3.059078] [mmc]: get mmc0's sdc_power is null!
[ 3.060209] usb 2-1.1: new low-speed USB device number 3 using sunxi-ehci
[ 3.082751] [mmc]: get mmc1's sdc_power is null!
[ 3.093453] [mmc]: get mmc1's 2xmode ok, val = 1
[ 3.104081] [mmc]: get mmc1's ddrmode ok, val = 1
[ 3.114210] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
[ 3.127183] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timinB
[ 3.145302] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timinB
[ 3.164039] usbcore: registered new interface driver usbhid
[ 3.175193] usbhid: USB HID core driver
[ 3.187914] asoc: sndcodec sunxi-codec mapping ok
[ 3.201419] asoc: sndhdmi sunxi-hdmiaudio.0 mapping ok
[ 3.213352] generic-usb 0003:1A2C:0002.0001: input,hidraw0: USB HID v1.10 Ke0
[ 3.213396] oprofile: using arm/armv7-ca7
[ 3.241233] u32 classifier
[ 3.244881] generic-usb 0003:1A2C:0002.0002: input,hidraw1: USB HID v1.10 De1
[ 3.267536] Actions configured
[ 3.276671] Netfilter messages via NETLINK v0.30.
[ 3.287367] nf_conntrack version 0.5.0 (15996 buckets, 63984 max)
[ 3.301521] ctnetlink v0.93: registering with nfnetlink.
[ 3.312330] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.325013] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.336742] xt_time: kernel timezone is -0000
[ 3.340214] usb 2-1.3: new low-speed USB device number 4 using sunxi-ehci
[ 3.359362] IPv4 over IPv4 tunneling driver
[ 3.369524] gre: GRE over IPv4 demultiplexor driver
[ 3.380143] ip_gre: GRE over IPv4 tunneling driver
[ 3.391155] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.402381] arp_tables: (C) 2002 David S. Miller
[ 3.412771] TCP: cubic registered
[ 3.421662] Initializing XFRM netlink socket
[ 3.431795] NET: Registered protocol family 10
[ 3.442852] Mobile IPv6
[ 3.450781] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.462119] IPv6 over IPv4 tunneling driver
[ 3.472798] NET: Registered protocol family 17
[ 3.477299] generic-usb 0003:0458:003A.0003: input,hidraw2: USB HID v1.11 Mo0
[ 3.501841] NET: Registered protocol family 15
[ 3.512341] Bluetooth: RFCOMM TTY layer initialized
[ 3.523237] Bluetooth: RFCOMM socket layer initialized
[ 3.534379] Bluetooth: RFCOMM ver 1.11
[ 3.543939] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.555283] Bluetooth: BNEP filters: protocol multicast
[ 3.566535] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.578657] L2TP core driver, V2.0
[ 3.587868] PPPoL2TP kernel driver, V2.0
[ 3.597615] L2TP IP encapsulation support (L2TPv3)
[ 3.608392] L2TP netlink interface
[ 3.617577] L2TP ethernet pseudowire support (L2TPv3)
[ 3.628675] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5
[ 3.642653] ThumbEE CPU extension supported.
[ 3.652813] Registering SWP/SWPB emulation handler
[ 3.664258] cmdline,disp=
[ 3.672598] [HDMI] power vcc-hdmi-18
[ 3.712638] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:58:08)
[ 3.727058] ths_fetch_sysconfig_para: type err device_used = 1.
[ 3.740412] CPU Budget:Register notifier
[ 3.750327] CPU Budget:register Success
[ 3.759994] sunxi-budget-cooling sunxi-budget-cooling: Cooling device regist0
[ 3.777719] [rf_pm]: select module num is 7
[ 3.787905] [rf_pm]: module power0 name vcc-wifi-33
[ 3.798775] [rf_pm]: failed to fetch module_power1
[ 3.809550] [rf_pm]: mod has no chip_en gpio
[ 3.819679] [rf_pm]: failed to fetch lpo_use_apclk
[ 3.830335] [rf_pm]: regulator on.
[ 3.839563] [wifi_pm]: wifi gpio init is OK !!
[ 3.849774] ALSA device list:
[ 3.858212] #0: audiocodec
[ 3.866437] #1: sndhdmi
[ 3.876576] Freeing init memory: 3384K
[ 4.125051] [mmc]: mmc 0 detect change, present 1
[ 4.320100] [DISP] disp_device_attached_and_enable,line:159:attched ok, mgr09
[ 4.640076] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timingB
[ 4.659232] [mmc]: sdc0 power_supply is null
[ 4.690048] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 4.722355] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO!
[ 4.738049] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO!
[ 4.748027] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 4.772408] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 4.790570] *******************Try sdio*******************
[ 4.803242] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !
[ 4.817944] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !
[ 4.832484] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !
[ 4.846454] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !
[ 4.856432] *******************Try sd *******************
[ 4.870650] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 4.885745] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 4.903221] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 4.941513] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1B
[ 4.958691] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1B
[ 4.973681] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1B
[ 4.988612] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4B
[ 5.003466] mmc0: new high speed SDHC card at address 59b4
[ 5.014511] mmcblk0: mmc0:59b4 SD 14.7 GiB
[ 5.025223] mmcblk0: p1 p2
[ 5.033423] *******************sd init ok*******************
[ 5.959243] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incoms
[ 6.050977] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incoms
[ 6.174425] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. )
[ 6.670244] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SE)
[ 6.691605] systemd[1]: Detected architecture 'arm'.
[ 6.755740] systemd[1]: Failed to insert module 'autofs4'
[ 6.770453] systemd[1]: Set hostname to .
[ 7.081716] systemd[1]: Starting Forward Password Requests to Wall Directory.
[ 7.095354] systemd[1]: Started Forward Password Requests to Wall Directory .
[ 7.108611] systemd[1]: Expecting device dev-ttyS0.device...
[ 7.125093] systemd[1]: Starting Remote File Systems (Pre).
[ 7.146369] systemd[1]: Reached target Remote File Systems (Pre).
[ 7.158091] systemd[1]: Starting Encrypted Volumes.
[ 7.173667] systemd[1]: Reached target Encrypted Volumes.
[ 7.184582] systemd[1]: Starting Dispatch Password Requests to Console Direc.
[ 7.198511] systemd[1]: Started Dispatch Password Requests to Console Direct.
[ 7.212295] systemd[1]: Starting Paths.
[ 7.226768] systemd[1]: Reached target Paths.
[ 7.236604] systemd[1]: Set up automount Arbitrary Executable File Formats F.
[ 7.252059] systemd[1]: Starting Swap.
[ 7.266476] systemd[1]: Reached target Swap.
[ 7.276134] systemd[1]: Expecting device dev-mmcblk0p1.device...
[ 7.292951] systemd[1]: Starting Root Slice.
[ 7.307935] systemd[1]: Created slice Root Slice.
[ 7.318107] systemd[1]: Starting User and Session Slice.
[ 7.334425] systemd[1]: Created slice User and Session Slice.
[ 7.345839] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 7.363916] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 7.376868] systemd[1]: Starting Delayed Shutdown Socket.
[ 7.393658] systemd[1]: Listening on Delayed Shutdown Socket.
[ 7.405165] systemd[1]: Starting Journal Socket (/dev/log).
[ 7.421960] systemd[1]: Listening on Journal Socket (/dev/log).
[ 7.433592] systemd[1]: Starting udev Control Socket.
[ 7.454787] systemd[1]: Listening on udev Control Socket.
[ 7.465911] systemd[1]: Starting udev Kernel Socket.
[ 7.481934] systemd[1]: Listening on udev Kernel Socket.
[ 7.492957] systemd[1]: Starting Journal Socket.
[ 7.508824] systemd[1]: Listening on Journal Socket.
[ 7.519583] systemd[1]: Starting System Slice.
[ 7.535252] systemd[1]: Created slice System Slice.
[ 7.545943] systemd[1]: Started File System Check on Root Device.
[ 7.557945] systemd[1]: Starting system-getty.slice.
[ 7.574479] systemd[1]: Created slice system-getty.slice.
[ 7.585825] systemd[1]: Starting system-serialx2dgetty.slice.
[ 7.603414] systemd[1]: Created slice system-serialx2dgetty.slice.
[ 7.615778] systemd[1]: Mounted POSIX Message Queue File System.
[ 7.627822] systemd[1]: Mounted Huge Pages File System.
[ 7.639198] systemd[1]: Starting Create list of required static device nodes.
[ 7.731000] systemd[1]: Starting udev Coldplug all Devices...
[ 7.871485] systemd[1]: Mounting Debug File System...
[ 7.966644] systemd[1]: Starting Load Kernel Modules...
[ 8.042746] systemd[1]: Started Set Up Additional Binary Formats.
[ 8.058036] systemd[1]: Starting LSB: Set keymap...
[ 8.133882] RTL871X: module init start
[ 8.146102] RTL871X: rtl8189es v4.3.0.4_11916.20140724_COB
[ 8.158888] RTL871X: build time: Aug 27 2015 21:55:02
[ 8.170462] systemd[1]: Starting Journal Service...
[ 8.183227] [wifi_pm]: set wl_reg_on 0 !
[ 8.244330] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timingB
[ 8.262102] [mmc]: sdc1 power_supply is null
[ 8.279937] systemd[1]: Started Journal Service.
[ 8.290086] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 8.312427] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 52, RTO!
[ 8.313260] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 52, RTO!
[ 8.313287] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 8.315800] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 8.317733] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 8, RTO !
[ 8.317776] *******************Try sdio*******************
[ 8.318590] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.319436] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.320273] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.321108] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.321137] *******************Try sd *******************
[ 8.321950] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.322781] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.323614] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.324444] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.324470] *******************Try mmc*******************
[ 8.324482] [mmc]: sdc1 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 tB
[ 8.325422] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 1, RTO !
[ 8.325457] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timinB
[ 8.325584] [mmc]: sdc1 power_supply is null
[ 8.328187] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timingB
[ 8.329726] [mmc]: sdc1 power_supply is null
[ 8.344315] [wifi_pm]: set wl_reg_on 1 !
[ 8.344552] RTL871X: module init ret=0
[ 8.350089] [mmc]: sdc1 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 8.372625] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 52, RTO!
[ 8.373723] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 52, !
[ 8.373747] [mmc]: sdc1 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 8.376360] [mmc]: sdc1 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 tB
[ 8.378544] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 8, RTO !
[ 8.378566] *******************Try sdio*******************
[ 8.379644] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.380734] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.381824] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.382914] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 5, RTO !
[ 8.382934] *******************Try sd *******************
[ 8.384010] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.385100] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.386191] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.387280] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 55, RTO!
[ 8.387301] *******************Try mmc*******************
[ 8.387309] [mmc]: sdc1 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 tB
[ 8.388491] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 1, RTO !
[ 8.388516] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timinB
[ 8.388624] [mmc]: sdc1 power_supply is null
[ 8.391204] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timingB
[ 8.392727] [mmc]: sdc1 power_supply is null
[ 8.410029] [mmc]: sdc1 set ios: clk 200000Hz bm PP pm