What is an electrical enclosure? I’m sure you’ve asked that question many times! Well, maybe not. But it’s something you should be aware of, so we present an overview here for you. An electrical enclosure is simply a box that holds electrical components. Let’s find out more.
History of Enclosures
In the early days of electrical power, switches were known as cut-outs. The name may derive from its use to “cut out” the power source. A simplistic term but effective and easily understood at the time. The cut-out was basically a simplified switch made of copper bars with an insulated “T” handle for the person to grasp for operation. The cut-out was mounted with bolts or screws to a wood, slate, or mica surface. It was visible and accessible as were its open live parts. There was no such thing as a qualified person because few people really knew the power and danger of electricity. The term cut-out is still used in the NEC today.
Cut-outs were installed in the open, and later placed in cut-out boxes. These are the switch enclosures of today.
In the early days of electricity, switchboards were exactly that: Switches mounted vertically on a board with open copper busbars. Live parts were open and exposed. Large fuses or Edison-base fuseholders were used to limit the amount of current flow. There were no circuit breakers as we know them. Electricity was used primarily for electric light and then for electric motors. The original electrical conduits were gas lines, which were already installed in buildings, and converted to carry wires for electrical circuits. There were lots of opportunities for fires or for people to fall into live parts.
Electrical power brought into homes in those days consisted of a knife-switch cut- out with cartridge and Edison-base fuses and open copper busbars and connections that were installed without an enclosure on a covered porch. People learned quickly that getting too close to the electrical service was uncomfortable and scary. It could even be deadly. Therefore, to improve safety, they installed the live parts in a wood cabinet. Hence the term “cabinet” that is still used in the NEC today.
The cabinet employed was similar to the cupboard where they placed dishes in the kitchen. This was a definite improvement over exposed live parts, but when other uses were discovered for electricity and taps were added to the existing system, loose connections and overheating sometimes occurred, which started fires. Cabinets made of dry wood were a fire hazard therefore metal cabinets were developed, which were more fire resistant.
Terminology
A look at present day Articles 312, 314, 404, and 408 shows the correlation in the NEC. The cut-outs referred to in Article 312 are today’s switches, also known as disconnects, pull-outs, etc. The term cut-out today is commonly used for a utility-type switch on systems that operate at 5 KV or higher. Code Making Panel 9 accepted a proposal in the 2011 NEC cycle to add the term “enclosed switches” to Section 312.8 for clarification.
It is important to note that the switch or cut-out is the switch mechanism and that it is installed in an enclosure. The enclosure may be a cut-out box, cabinet, switchboard, or other type of enclosure. In Article 404, Section 404.3(A) tells us that generally, switches and circuit breakers “shall be of the externally operable type, mounted in an enclosure listed for the intended use” and refers to Section 312.6 for wire bending space. Exception 1 still permits open-knife switches on an open-face switchboard or panelboard without enclosures. The switch may be fused or unfused or could be a circuit breaker used as a switch or a molded case switch, which contains no overcurrent protection.
Panelboards are the same way. The panelboard is mounted in a cabinet or enclosure. The internal parts of the panelboard are the overcurrent devices – the circuit breakers or fuses – mounted on the busbars and support rails. A review of Article 408, in Section 408. 2, refers to Article 312 for requirements for panelboard enclosures.
Enclosures can also be a fenced area, as seen in the definition of enclosures found in Article 100: “The case or housing of an apparatus, or the fence or walls surrounding an installation to prevent personnel from accidentally contacting energized parts or to protect the equipment from physical damage.”
Enclosures often contain overcurrent devices. In Section 240.24(C), overcurrent devices are to be located where they will not be exposed to physical damage. But enclosures contain more than overcurrent protective devices. They also contain conductors and other electrical equipment such as relays, timers, motor controllers, and more. A fence or wall surrounding electrical equipment can be an enclosure, such as an electrical substation or switchyard that encloses live buss, transformers, switches, circuit breakers, reclosers, reactors, etc.
Enclosures
NEC Section 110.28 lists the types of enclosures: “Enclosures (other than surrounding fences and walls) of switchboards, switchgear, panelboards, industrial control panels, motor control centers, meter sockets, enclosed switches, transfer switches, power outlets, circuit breakers, adjustable speed drive systems, pullout switches, portable power distribution equipment, termination boxes, general-purpose transformers, fire pump controllers, fire pump motors, and motor controllers.” Even standard device and junction boxes for snap switches, ground fault circuit interrupter or standard duplex receptacles, motion sensors, fire alarm pull stations, or a variety of other devices are enclosures, and the basic rules in Articles 312 and 314 apply to them.
Enclosures simply enclose electrical conductors and equipment. Table 110.28 is a useful tool for the electrical engineer, designer, or installer. It provides guidance for selection of enclosures for specified indoor or outdoor locations in standard National Electrical Manufacturers Association (NEMA) types. Requirements for enclosures located in hazardous or classified locations are found in Chapter 5 of the NEC.
Finish this article here:http://www.ieci.org/newsroom-and-insights/enclosures-whats-in-the-box
There are electrical enclosures all around you; once you start looking for them, you’ll see them everywhere. It’s important to know about them because they pose a danger if something goes wrong. If anything goes wrong electrically in your home, we’re here to help sort it out and get it fixed the right way. Trust our experience and our care for our customers and you won’t be disappointed. Give us a call whenever you need help..
Related posts:
A Tripping Circuit Breaker Can Indicate a Serious Electrical Problem
Should a Novice Replace a Breaker Box Switch?
Improve your Home’s Electrical Safety